For clean and safe chop and miter cuts in non-ferrous metals, plastics and wood.

Chop and Miter Saw KGS 80

Ideal for miter cuts. Instead of swiveling the saw head, the table with clamped down work piece is turned!

By using the fence and counter-rotating the table 2x 45°, one can get the opposite angles for two equally long framing pieces by simply reversing them. Powerful, very quiet DC motor. Power transfer via belt drive. Carbide tipped saw blade 80 x 1.6 x 10mm (3 1/8" x 1/16" x 3/8"), 36 teeth.

Other technical data:

Volts 110 - 120V AC, 60Hz
Max. Power 1/4hp (200W)
Speed 5,400rpm
Table area 9" x 9" (230 x 230mm)
Weight 12 lb (6kg)


Base with round table of pressure-cast aluminum and CNC-machined guides and fittings.

NO 37 160

See us on YouTube!



California Residents Prop 65 Information


WARNING:
This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.





Video KGS 80


  1. Saw head moves laterally making it possible to get extremely close to the vise holding the work piece when making the cut affording a vibration- and burr-free cut.
  2. With longitudinal fence stop (overhang 300mm/12").
  3. Ergonomically correct grip with integrated switch and saw head release mechanism.
  4. Continually adjustable (may be tightened in any position) round table made of pressure-cast aluminum swivels 45° in both directions with positive stops at 15° intervals.
  5. Integrated tightening mechanism with self-centering clamps. V-groove for round pieces. Front side groove for clamping thin work pieces.

Cutting capacity at 90° (Perpendicular cut):

With material thickness up to
(in mm and inch)

Maximum material width
(in mm and inch)

Maximum round stock diameter
(in mm and inch)

10
18
21
25

3/8"
11/16"
13/16"
1"

65
50
40
25

2 9/16"
2"
1 9/16"
1"

Ø 25

Ø 1"


Cutting capacity at 45° (Miter cut):

With material thickness up to
(in mm and inch)

Maximum material width
(in mm and inch)

Maximum round stock diameter
(in mm and inch)

5
10
15
20

3/16"
3/8"
9/16"
3/4"

36
30
25
18

1 13/32"
1 3/16"
1"
11/16"

Ø 20

Ø 3/4"

High-alloy special steel (HSS)
Use on non-ferrous metals, soft and hard woods, laminates, GRP, CFK and composite boards.
Also fits circular table saw FET.

NO 28 730   3 1/8" x 3/64" x 3/8" (80 x 1.1 x 10mm), 250 teeth


Synthetic resin bonded cut-off wheel
For cutting wood, steel, non-ferrous metals and plastics.

NO 28 729   3 1/8" x 3/64" x 3/8" (80 x 1.0 x 10mm)



Carbide tipped saw blade
Extremely clean cutting edges when cutting balsa wood, plywood or soft wood as well as glass-fiber reinforced plastics (GRP) because of large number of teeth. May also be used for cutting hard wood, POLYCARBONATE, plastics and aluminum.
Also fits circular table saw FET.

NO 28 732    3 1/8" x 1/16" x 3/8" (80 x 1.6 x 10mm), 36 teeth