Optimal for milling, drilling, routing, polishing, cutting, cleaning, brushing, deburring, sawing, engraving, carving.

MICROMOT 50





The standard 20mm collar allows use in the drill stands MB 140/S and MB 200 as well as in the universal holder UHZ.
Stable housing of glass-fibre reinforced POLYAMIDE. With a soft component in the finger grip area.

MICROMOT 50/E



These two lightweight high precision tools in a pen style design (Ø only 1 3/8") are ergonomically formed to allow comfortable handling and optimal control. Their quietness and effortless, vibration- free drive via the special permanent magnet motor, the ground spindle and collar bearing all contribute to the ergonomic design. An efficient cooling system facilitates extended use under various load conditions. Both tools are useable on any workable material e.g. steel, precious metals, wood, glass, ceramics, plastics, precious stones. They are ideal for model builders, woodcarvers, jewelers, opticians, artists, dental technicians, tool and die makers, etc.


Rotary Tool MICROMOT 50/E

Technical data:
Direct voltage 12 - 18V. Power absorption up to 40W input. 5,000 - 20,000/min. Length: 8 21/32" (220mm). Weight: 0.51 lb (230g). Six MICROMOT steel collets (one each in size 1/32", 1/16", 5/64", 3/32", 7/64" and 1/8" (1.0 - 1.5 - 2.0 - 2.4 - 3.0 and 3.2mm) are included.

NO 28 510


Rotary Tool MICROMOT 50


Same as 50/E, except without speed control. Load speed is 20,000rpm. If you run this machine while using our transformer NG 5/E as power supply, speeds are adjustable between 5,000 and 20,000rpm via the speed control on the work station. Six MICROMOT steel collets (one each in size 1/32", 1/16", 5/64", 3/32", 7/64" and 1/8" (1.0 - 1.5 - 2.0 - 2.4 - 3.0 and 3.2mm) are included.

NO 28 500






Video MICROMOT 50/E



  1. The standard 20mm collar allows use in the drill stands MB 140/S and MB 200 as well as in the universal holder UHZ.
  2. Stable housing of glass-fibre reinforced POLYAMIDE. With a soft component in the finger grip area.





Note:
The speed control of our 12 volt devices only works when operated via non-stabilised power supply units. We recommend our MICROMOT mains adapters NG 2/S and NG 5/E. Connection to stabilised power supply units is possible. However, the devices will then operate with maximum rotational speeds (also applies to operation with batteries).


WARNING:
This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

MICROMOT Steel Collet Set
Fits all MICROMOT machines, except the engraver GG 12. One each in size 1/32", 1/16", 5/64", 3/32", 7/64" and 1/8" (1.0, 1.5, 2.0, 2.4, 3.0 and 3.2mm) come as a set in a practical holder for storage along with one clamping nut.

NO 28 940



NOTE: The collet makes a big difference!

MICROMOT steel collets are hardened and have a high, consistent flexibility so that they maintain their accuracy, even if used regularly.

The triple slit collet offers a substantially better load bearing surface than the easier to produce four-slit type. This is especially important for cutters with small shank diameters.


Quality, triple-slit hardened steel collets are ideal for optimum concentricity and tightening force. Furthermore, bits and cutters may be fitted close to the chuck. This is especially important when sanding, routing and milling as side play is minimized.